Cb radio hook up instructions


Larger radios need to be installed with the bracket. For a good source for DIN in dash radio mounting hardware, check out our mounts and brackets page. Also, a lot of people seem to like the hump mounts. Do not key your mic before the antenna is installed! If you do, you risk damaging or destroying your radio! You'll find a great selection of antennas on our mobile antennas page.

If you prefer a low profile antenna, the Walcott short 2 foot antenna that looks about the same as a car antenna is available for motorcycles , pickup trucks and cars. On a car, the best place is on the middle of the roof - unless you have a fiberglass car or a sunroof. That way, your roof serves as the antenna's ground plane to provide good signals in each direction. Other locations, not quite as good, include: Some of these installations require holes to be drilled into your roof, trunk or fender, which require rustproofing and weatherproofing.

A less invasive installation can be done using magnetic mounts , but the magnet must be strong enough to secure the antenna even at highway speeds. The ground plane surface is a major consideration when deciding where to place your CB antenna. Ideally, the best place is in the center of your roof.


  • singles ladies dating site?
  • best muslim dating sites canada.
  • .
  • Power wire hookup - battery or cigarette plug;
  • .

Roof mounted antennas provide the best ground plane and a degree radiating surface to transmit your signal. However, most people don't want to drill holes in the center of their roof. The next best location is to mount the antenna on the fender or trunk. Examine your vehicle to determine the best location for the antenna to be mounted where it will have the most metal surface to radiate from. Keep in mind that when you mount your antenna on the edge or side of the vehicle a degree radiating pattern will not be achieved.

The transmission of the signal will be limited on that side of the vehicle. If you mount an antenna on the front driver side fender, your signal will not transmit well to the front right of the vehicle where the antenna has no ground plane.

Basic CB Radio Installation and Troubleshooting | harhguatynora.ga

The signal will transmit very well to the back right of the vehicle. To achieve the best performance an antenna mounted in the fender should be at least six inches over the roof, which enables additional ground plane surface for transmission.


  • .
  • .
  • love shack dating divas.

Some antennas, including center- and continuous-loaded antennas don't include mounting hardware or cable. Others come with complete kits that include: If yours doesn't come with a mounting kit, get stainless steel or weather-coated metal antenna mounts. There are a variety of mounts available. A couple of pieces of optional antenna equipment can make CB life even better: People use dual antennas because they co-phase, changing the radiation pattern by forming two overlapping figure eights, thus increasing transmission strength to the front and back.

This is a benefit because CB users usually want to talk to those in front or behind them rather than to quickly passing oncoming traffic.

Basic CB Radio Installation and Troubleshooting

When installing two antennas, they should be about six feet apart. Both antennas require sufficient ground plane, grounding, a sturdy mounting hardware and good quality coax. When you consider how to hook up a CB radio, be sure to use thickly insulated coaxial cable coated to protect against the weather, such as the RG or RG cable , and stainless steel or metal connectors such as the Motorola type or PL which has a large connector.

Now, how to wire a CB radio - that means that you'll need to run your coaxial cable from the antenna to the CB radio plus provide a source of power to run the radio. How you'll do that depends on your vehicle.

Choosing a Radio

You may need to run cable from the trunk lid through the back seat, then under the doorframe and window pillar or the dash and firewall. You have a couple of options to provide power to your CB radio: Things to consider are making sure to have a fuse in the power line before the vehicle firewall and ensuring that your CB radio is turned off preferably automatically when the car isn't running. For instance, using a cigarette plug may allow the power to be always on, quickly draining the battery.

You will find very short stubby CB antennas no taller than a foot with a magnetic mount. Though they seem ideal for offroad use, avoid them. They are hard to adjust the SWR and get terrible range. Bolt on brackets include a wide variety of bolt-on antenna mounts that come in all kinds of custom designs for various locations on the vehicle. Hood mounts, corner mounts, vehicle specific location mounts, even rollbar and roof rack mounts. Worry free, will not get knocked over or off the vehicle.

Cons — Permanently mounted, may require drilling. Challenge to find a location. The most common, versatile CB antennas come as steel whips and fiberglass tube antennas of various heights. Most common antennas use the quarter wave length about 9 feet with most of the antenna wound up as a coil. Steel Whip antennas are nice because they flex well and most steel whip antennas will have a base-loaded coil keeping the bulk of the antenna away from branches.

http://outer-edge-design.com/components/arsenal/1700-smartphone-tracker-on.php Fiberglass antennas will flex somewhat but coupled with a spring mount, will resist damage. Some fiberglass antennas have the benefit of being center-loaded and top-loaded putting most of the antenna as high as possible for better output and reception. Though not unbreakable, fiberglass is strong and light-weight.


  • CB Radio Installation: How to Install, Set Up & Hook Up!
  • carbon dating ppt.
  • .
  • .
  • ?

Center-loading or top-loading a steel antenna adds additional weight or bulk to the center or top of the antenna, which is not ideal for off-road use. All CB antennas shorter than a inch whip have a coil. The wire in the coil is the remainder of quarter wave inches minus the height of the antenna itself wrapped up in a tight or spread out coil. The location of the coil affects output because the higher the coil is on the antenna, the higher the bulk of the antenna is in relation to the ground and the vehicle. Antennas can be base-loaded, center-loaded, top-loaded or continuous-loaded.

How do you identify what type of antenna is what? Base-Loaded — Base loaded antennas have the bulk of the antenna at the bottom of the antenna within a sealed plastic base, usually attached to the magnet or secured to the roof of the vehicle. Most magnetic mount antennas are base loaded due the weight and bulk of the coil. Center-Loaded — Center loaded antennas usually have the coil further up the antenna but not always in the center. Center loaded antennas will generally have a thicker steel shaft up to the coil for support. Top-Loaded — Top loaded antennas are very common and inexpensive yet are also the most efficient.

Top loaded CBs are usually fiberglass construction with a thin wire wrapped around the fiberglass pole and covered in a protective layer of vinyl plastic. The thin wire is wrapped tighter towards the top placing most of the wire near the top. Benefits of a top-loaded fiberglass antenna is that option to mount the antenna lower on the vehicle yet placing most of the antenna higher, hopefully above the roofline of the vehicle.

Unsealed 4X4 Garage - Project Rusty: GME UHF Install

Continuous-Loaded — Continuous loaded antennas are very similar to top-loaded antennas in their construction with the exception of the wire distribution over the shaft. With continuously loaded antennas, the wire is not concentrated towards the top or bottom, but rather distributed evenly over the entire length of the shaft. Most of these type plugs are rated at amps of power.

You should check your fuse box or manual to find out the rating and amps provided for your outlets.

Who Uses CB Radios and Why?

If your CB radio requires more than 20 amps such as a Galaxy 95T or Ranger high power version you will need to wire your radios directly to the battery. However you wire your radio remember to use the appropriate gauge of wire, completely cover and protect any wire connections, make sure there is no bare wire that is exposed, and always use appropriate fuses rated for your radio. This website is purely for entertainment purposes. Any and all articles, reviews, products, pictures, writings or any other material published on this website are written and are to be used for entertainment purposely only.

cb radio hook up instructions Cb radio hook up instructions
cb radio hook up instructions Cb radio hook up instructions
cb radio hook up instructions Cb radio hook up instructions
cb radio hook up instructions Cb radio hook up instructions
cb radio hook up instructions Cb radio hook up instructions
cb radio hook up instructions Cb radio hook up instructions

Related cb radio hook up instructions



Copyright 2019 - All Right Reserved